T R LANE  - Company Message
GP ROLL BAR FITTING INSTRUCTIONS
 
1.  MOVE BOTH SEATS FORWARD, TILTED FORWARD, GIVING ACCESS
     TO REAR AREA.   POSITION HOOD IN DOWN POSITION.  REMOVE
     SEAT BELT SHOULDER STRAPS FROM TOP OF SEAT BELT TOWERS.
     REMOVE PLASTIC COWLING SURROUNDING SEAT BELT TOWERS,
     GIVING ACCESS TO SEAT BELT REELS.  REMOVE YOUR PARCEL
     SHELF CARPET AND FIRE WALL CARPET.  REMOVE PARCEL SHELF
     TRAY, TAKING GREAT CARE AS THIS ITEM CAN BE VERY SHARP.
     THIS WILL GIVE YOU ACCESS TO WHERE THE ROLL BAR NEEDS TO
     SIT. 
 
2.  JACK UP CAR,  SECURELY UPON AXLE STANDS.  REMOVE REAR
     WHEELS.  REMOVE SPLASH TRAYS WHICH ARE LOCATED IN FRONT
     OF THE REAR WHEELS, IN FRONT OF THE ARCHES.  WHERE ROLL BAR
     SITS IN CAR, YOU WILL NEED TO LOOSEN ALL FIXINGS WHICH
     HOLD WIRING HARNESSES IN POSITION.  THERE ARE ALSO THREE
     SMALL BOLTS ON EACH SIDE OF THE SEAT BELT TOWERS BY YOUR
     WIRING HARNESSES - THESE NEED TO BE REMOVED.   THE TWO
     ANGLE BRACKETS WHICH THE REAR PARCEL SHELF MOUNTS TO,
     YOU WILL NEED TO REMOVE 4" OF THIS EACH SIDE, ENABLING YOUR
     ROLL BAR TO SIT NEATLY BETWEEN SEAT BELT TOWERS.
 
3.  PROCEED TO FIT ROLL BAR IN POSITION, USING YOUR SEAT BELT
     TOWER BOLTS, LOCATE THE ROLL BAR SIDE MOUNTING PLATES,
     YOU MAY NEED TO MAKE SOME SPACERS OR YOU CAN USE
     EXISTING TOP HAT SPACERS THAT HAVE COME OFF YOUR 
     SHOULDER STRAP BOLTS.  PROCEED TO LIGHTLY TIGHTEN THESE
     BOLTS, ENSURING THAT THE ROLL BAR FEET PLATES ARE SITTING
     ON THE CHASSIS AREA.  ADJUST YOUR ROLL BAR SO THAT THE
     FEET PLATES SPREAD OUT NEATLY BETWEEN THE SEAT BELT
     TOWER SIDES (THERE MAY BE A GAP IF A HARNESS BAR IS 
     PROVIDED DUE TO WELDING HEAT DISTORTION) BUT THIS CAN
     BE OVERCOME BY BOLTING TO THE SIDES OF PILLARS. 
 
4.  WITH A CENTRE PUNCH, PUNCH DOWN THROUGH THE HOLES AS
     HARD AS YOU CAN, THEN YOU WILL FEEL UNDER THE CAR WHERE
     YOU HAVE PUNCHED DOWN THROUGH, PUNCH BACK UP THROUGH
     FROM UNDERNEATH, THEN WITH A PILOT DRILL, DRILL UP THROUGH
     AND THEN DRILL AGAIN WITH APPROPRIATE DRILL.  BOLTS DOWN
     THROUGH, THERE ARE BACKING PLATES TO BE ATTACHED ON
     REAR STAYS WHICH CAN NOW BE TIGHTENED IN POSITION. 
 
5.  REMOVE SEAT BELT REELS, YOU MAY PROCEED TO DRILL THROUGH
     THE SIDE MOUNTING PLATES AND THEN PROCEED TO NUT AND
     BOLT TOGETHER, AND THEN RE-ATTACH SEAT BELT REELS. 
     (AS A SAFETY MEASURE, GET A SECOND PERSON TO CHECK THAT
     YOU HAVE TIGHTENED THE SEAT BELT REELS).  FINALLY CHECK
     THAT YOU HAVE TIGHTENED ALL THE NUTS AND BOLTS.  WHEN
     YOU ARE HAPPY WITH INSTALLATION, YOU MAY PROCEED TO
     REPLACE SPLASH TRAYS, FIX WHEELS, SET BACK DOWN ON THE
     FLOOR. 
 
6.  YOU WILL NOW NEED TO TRIM YOUR REAR PARCEL SHELF AREA.
     THIS IS UP TO THE INDIVIDUAL HOW THEY WISH TO DO THIS. 
     ONCE YOU HAVE FITTED THE PARCEL SHELF, YOU WILL THEN
     NEED TO TRIM THE BOTTOM EDGES OF THE SEAT BELT COWLINGS,
     ENABLING THEM TO SLIP FROM THE COCKPIT AREA BACK TOWARDS
     THE BACK OF THE CAR, SLIDING BETWEEN THE ROLL BAR AND
     SEAT BELT TOWERS.  THIS CAN SOMETIMES BE A TIGHT FIT AND
     MAY NEED SOME GENTLE PERSUASION AND EASING.  THEN
     PROCEED TO FIT PARCEL SHELF CARPET AND TRIM AS DESIRED. 
    
 
T.R. Lane Fabrications or any employee of T.R. Lane Fabrications are not in anyway responsible or liable for loss or injury to any persons whilst fitting or using this roll bar.
This is part of the sale agreement.